uSED mACHINERY - uSED sTEEL fABRICATING mACHINERY

USED BEHRINGER MITERING BAND SAW

Large, heavy duty dual column dual mitering band saw complete with automatic infeed measuring shuttle system.

Installed new in 1997, will cost over $130,000 to replace this machine today. Less than 12,000 hours. In excellent condition.

PRICE USD $55,000 F.O.B. Warehouse

Equipped with:

• Large Dual Column - Parallel Down-Feed Design
• Fully Automatic Hydraulic Carbide Blade Guides
• Fully Automatic Hydraulic Blade Tensioning
• Front Material Clamp
• Manually Adjustable Cutting Pressure and Feed Rate
• Fully Automatic with BT 20 control station dual miter programming
• Feed Carriage with Clamp
• Flood Coolant
• Side Exit Chip Conveyor
• Rapid Approach Sensor
• Chip Conveyor
• Input and Output Roller Conveyors
• Horizontal and Vertical Clamping

Transfluid Compact Mandrel Bending Machine

Fast and practical bending of hydraulic tube, pipes and tubes; with fast and simple tool change over, repeatability and precision.

Machine put into use in 2008,  just two years old!

Machine includes Tooling: (1) 2.5" die and (1) 3.0" die for tube.

Model B 2060 K

• Max. round tube size - inches (mild steel) 3" x .109"     
• Max. steel pipe – 2” Sch. 40
• Max. square tube size - inches (mild steel) 3" x .109"    
• Max modulus of section 12,0 cm3           
• Max. center line radius 6"           
• Tube arbor length 10', 15', 20'    
• Bending speed 90° (forward only) 8 sec.
• Motor 4 HP
• Bending angle max  190°
• Bending direction Right
• Number of digitally programmable bends 8
• Size in inches (without arbor), l x w x h 44 x 36 x 51        
• Weight in lbs. 2205

  PRICE USD $29,995.00

Used pEDDINGHAUS f1170/b – pLATE dUPLICTOR

• 170 ton punch - capable of punching 1-1/4” material
• 30” throat depth
• Fully CNC; Peddimat software
• Built 2006
• Serial number 48580

            Specifications

Used Ercolina Bender - LIKE NEW!!!

• This is an Ercolina Mega 030 Axis Mandrel Bender. It bends materials 3/8" to 3"
• ideal for small production applications
• CLR as small as 1.5D
• NC programmable C axis with manual X & Y positioning
• Ideal for bending thin wall mild steel, stainless steel, aluminum and other materials
• Programmable bend sequencing and mandrel retraction
• Independent clamp and pressure die adjustment
• Reinforced tool shaft with swing arm and tie bar support for maximum rigidity
• Micrometer wiper die adjustment
• Secondary hydraulic pressure die stabilization system
• Quick change tooling
• 10 foot table with pneumatic clamping and DRO system for linear and rotational positioning.

PRICE USD $27,000

Used scotchman band saw

• Model: SHA1419 Scotchman
• Head Swings 45 degrees - No Material Movement
• 3HP Variable Frequency Blade Drive Motor
• Fully Automatic
• Hydraulic Feed Control with Separate Adjustable Rate and Feed Pressure
• Programmable Length Control- NC - Rotary Encoder
• 40" Index Stroke with 8 X Multiple Index
• Hydraulic Full Stroke Vise, Full Capacity Vising
• Hydraulic Head Raise with Adjustable Head Lift Stop to increase Production
• Out of Stock Switch
• Infinitely Adjustable Blade Speed via AC Inverter
• Saw Guides, Spring Loaded, Solid Carbide Inserts for Clean Accurate Cuts
• Replaceable Steel Wear Plates on Bed
• Recirculating Flood Coolant System with Splash Guard
• Wash Down Hose with Hanger for Easy Cleanup
• Powered Blade Brush for Straight Cuts and Longer Blade Life
• Saw Blade Guard for Operator Safety
• Instruction and Parts Manual
• Made in USA

Options:

• Overhead Nesting Vise
• Variable Vise Pressure
• Roller Conveyor 10’

GREAT CONDITION   PRICE USD $14,000

Used Komatsu rasor cnc plasma cutter

• Used RASOR Model KCR 0951 5x10 Fine Plasma with 90amp high definition plasma unit.
• This machine also has the QuickSilver option for clean cutting of stainless steel and aluminum.
• We typically have used Nitrogen / Nitrogen + LP Gas with this option.
• It was built in 1998 and sold as a factory rebuilt and recertified machine in January 2007.
• Komatsu maintenance reps have work on the machine, and it has a new FinePlasma 90 Amp Torck and FinePlasma 90Amp Control Box, both installed in April of this year.
• Software for the machine is:
  Rasor Server v1.0 for windows98,SE/Me/NT/2K/XP,Rasor nest Application V2.0 with improved DXF and IGES conversion, PathMaster for windows 3D library

MACHINE IN GOOD SHAPE!  PRICE USD $55,000

used roundo angle bending roll

• Larger than Standard Diameter Shafts on Rolls (mm vs. mm)
• Machine is equipped with the Shafts, Motors, and Drives that are normally found on the R-15S Model machine, but in the R-13S Frame
• Machine Weight is approximately 120,000 Lbs.
• The approximate Foot Print of the Machine is 155” x 218”, not including the Pit
• Travel Speed of Materials through Machine:  aprox 23ft per min
• Digital Position Indicators for the (2) Rear Adjustable Rolls
• Roll Bolt & Cap Assemblies are made of (3) different height sections, which are split halves and can be removed easily for quick adjustment of the assembly
• Beam-on-Edge Device (Hydraulically Powered), with (3) Sets of Pulling Rolls
• Hydraulic Pressure Gauge in clear view during operation of device
• Adjustable Guide Rolls that are Hydraulically Controlled in (3) Directions:
• Up / Down; In / Out (Front to Back); and Rotating (Left / Right)

MACHINE WAS DELIVERED TO ORIGINAL OWNER IN 1996   

PRICE USD $950,000

Various Dies and Spacers including the following:

• Standard Set of Angle / Bar Rolling Dies(Grooved for capture of Beam Flanges when rolling the Easy Way)
• Set of Square / Rectangular Tubing Dies
• Dies are Reversible, and made for both 3/8” and ½” Wall Tubing
• Various Spacer Sets used for the Rolling of Beams on Edge, Rolling Beams and Channels the Easy Way, Spacing the Dies for Bars, Tubing, etc.

Used PIRAHNA HYDRAULIC SHEAR

• Machine still under power and working
   

Used PIRAHNA PRESS BRAKES

• Machine still under power and working
   

Used Ercolina Tube and Pipe Bender

• Ercolina 030 with pipe kit and 20ft 2-axis positioner
• Purchased new in 2002 and has undergone little use
• F.O.B. Ocala, FL

Used Ercolina Bender - LIKE NEW!!!

Used Scotchman Fully Automatic Cold Saw

This 5 year old Scotchman fully automatic saw for cutting small steel profiles has seen very little use as this recent picture shows. It is in exceptionally good condition and can be seen under power in South Florida.

Used Ficep 1001D Single Spindle Drill Line

Manufactured in 2003

• Machine is in excellent condition.  Current owner had monthly preventative maintenance performed on machine.
• Machine is under power and can be seen in operation.

Click here for more information on the Used Ficep 1001D Beam Drill Line

Used Cincinnati Shear

This used CINCINNATI Shear in good condition.

• 3/4" x 10ft
• Build date 1976, but looks much newer
• Model 6GL10
• 1 set extra blades

Used Metal Fabricating Systems (MFS) Series HD-145 CNC Drill

• Purchased new in 1988
• 3 hydraulic spindles
• Maximum beam size is W36x300 through drill
• Includes ~68 feet of INFEED conveyor and ~65’ of OUTFEED conveyor (transfer tables NOT included)
• Measuring device
• Control Booth

Used Trennjaeger PMC 16 Cold Saw

• Purchased new in 1988
• Saw has cut up to W14x550
• Saw can handle up to 39” widths.

Both machines are currently processing material, are well maintained and will remain in production until new machines are installed in July 2007.

Click here for Beam Saw Drill Line Layout. NOTE: Cross transfers not included.

Used Pangborn Shotblasting Machine

• 8 Wheel Shot Blast Machine
• 4 Wheels per side - 25HP each
• 8 Rotoblast assemblies (4 per side) w/ 12 vanes each powered by 25 hp motors.
• Dust Collector System  
• Pulse type w/ 12 paper filters @ 254 sq. ft. Each fan: 5620 cfm, 10.5" sp, 3500 rpm
• The machine was equipped from the factory w/ a 10' long hopper on the outlet side. An additional 10' long hopper on the inlet side was made by Pangborn and installed in 2004. An enclosed safety ladder was added for access to
  the top of the machine along with catwalks and safety railings.

Used American Hydraulic Shear

1980 – 3/4” x 12’  - American Hercules Hydraulic Shear – Very Good Condition

• 36” Front Operated Power Back Gauge
• Weight 52,000#   50-hp   9’ squaring arm  on left side   3’ squaring arm on right
• Two 4’ support arms in middle
• Over capacity setting for 1” plate and key operated blade clearance override
• 11” deep apron requires a small pit
• Still has original blades – 1 1/8” x 5” x 148”
• Location:  Homestead, FL

Used Hydrapower Hydraulic Press Brake

This used HYDRAPOWER Hydraulic Press Brake is in good condition.

•      Capacity: 120 Tons
•      Length overall 10'
•      Distance between housings 8'6"
•      Throat depth 8"
•      Open height 15"
•      Stroke 8"
•      2 x 10HP, 220/440v, 3ph

Used Peddinghaus Band Saw

Used Peddinghaus Band Saw  - Installed new in 1999 - Available in Central Florida

• Vertical Band Saw
• 1" blade (187" long)
• 24" vert x 20" horiz capacity at 90 degrees
• 3HP Motor 460 V 3Phase
• Power Driven Miter
• Miter cutting 60 degrees
• 50 - 460 ft per min
• Quick action vice

The BARGAIN of the YEAR!!!!!

Snap this up today - at this price it wont last long! Your only chance to buy a Used Beam Line, Plus a Used Peddinghaus band saw, plus cross transfers, plus conveyors at an incredibly low price.....

This equipment is sold as a bundle and includes

1. Used Peddinghaus Band Saw 18 x 38"

Model SHN 38/18 Peddinghaus Band Saw - Purchased new in 1997.

2. Used Fabriline Beam Punch Line with Controlled Automation Retrofit

The Beam line is a used Fabriline 3454-206 Hydraulic Beam Punch line. This sturdy beam line was upgraded with Controlled Automation panel view, computer and controls in 1997/98

3. Material Handling Equipment

The sturdy and robust material handling equipment is second to none - just take a look at the images. This includes

25’ crossover conveyors with

280’ of powered chain driven roller case hydraulic conveyer (new in 2003)

This equipment is stored in a warehouse for easy inspection by appointment

• Beam Line
• Band Saw
• Cross Transfers
• Roller Conveyors